Power Tools Heavy Duty 13mm Drilling Machine
|Unit Price:||6.0~14 USD|
|Terms of Trade:||FOB|
|Min. Order:||3000 Piece/Pieces|
|Delivery Time:||35 Days|
|Packaging:||color box packing|
|Place of Origin:||China|
Model No.: KID1301
Model : KID1301
Drill Capacity: 13mm
No-Load Speed: 0-2700r/min
Rated Input Power:600w
1 BE SURE TO CARRY OUT STRICTLY THE RELEVANT RULES IN GB3387 THE TECHNICAL RULES ON MANGEMENT,USE,CHECKING AND SAFE MAINTENANCE OF THE HANDLE ELECTIC TOOLS.OTHERWISE YOU MUST OBEY OUR EXPLANATION FIRST.
2 REGULARIZING WORKPIECE THE WORKPIECE TO BE DRILLED MUST BE REGULARIZED AND PAY MORE ATTENTION TO IT WHEN IT IS DRILLED THROUGH.
3 NOT TO USE POWER WIRE WITHOUT LIMITED.BE SURE NOT TO LENGTHEN OR CHANGE THE POWER WIRE,NOT TO CARRY THE POWER WIRE YOUCH HEAT SOURCE AND OIL.PREVENT THEFROM BEING DAMAGED.OPERATION:
1 USE ASSIGNED VOLTAGE The voltage in the cireuit must be not more than 10% at the date plate assignment before using it.
2 CHECK BEFORE BEING USED Let the tool have nonloading for one minute and see whether the function of transmission position is flexible and there is abnormal noise and the scraws become flexible and fall off and the inverting sparkle is normal or not.
3 PREVENT THE TOOL FROM OVERLOAD The head of the drill must be sharp.when you are drilling,you should not be too tough.If the rotation speed is reduced abnormally,you should reduce to exert yourself.If the drill stops suddenly or gets stuck,you turn off the power.
4 CHANGE THE BRUSH IN TIME If the brushes are too damaged to use,Change them both at the same time,otherwise the brushes and the inverter will be in loose contact even sparkle around or the inverter can be damaged.Sometimes the Armature would be burnt.
5 IT CAN NOT BE USED IN THE FOLLOWING CONDITION.If you find the insulate is danaged the power wire or electric cable case is briken, the plug and outlet is broken,and it works continually the sparkle appears seriously etc you should repair immediately.It can not be used before repaired.
6 USE THE TOOL CAREFULLY The tool used should be placed softly in order not to be shoched..MAINTENANCE:
1 ADD OIL IN IT OF TEN The drill is apeed working tool.The lubrication grease is volalilized easily so the grease in reduction case and bearing must often be kept clean and add or change it anytime needed.
2 CHECK AND MAINTENANCE ON IT FREQUENTLY.The drill should be checked.repalred day and see whether the power,the plug and the switch work well or not. Pay attention to everything such as whether the insulation resistance works normally,the handle is flexible,the inverter and brushes are well contacted,the armature winding and the stator winding are in shourt circuit or broken circuit,and the bearing,the other noving parts are damaged etc.
3 EACH PART SHOULD BE WELL KET AND WHEN YOU WANT TO CHANGE THE PART.USING THE SAME ONES When the drill neds taking apart and checking.Do keep each part including insulation linerand casing pipe.If they are damaged you must change the new one and the same one. Be sure not to use use the substitution materials which is worse than one used and the part which does not agree with the standard.When fixing,you must put the parts in their proper position as usual and should not omit any of them.
4 BE CAREFUL OF THEINSULATION RESISTANC The drill not to be used for long or to have been used in damp condition must be tested in its vinding of the insulation resistance with a 500 million ohm metet.If the winding and iron center is less than 2million ohms,you moust drying treatment to the winding unit more than 2 million ohms.
5 STORED CAREFULLY The drill should be kept in a sry clean place and without any corrosive gares.
NINGBO LUBAN ELECTRIC POWER TOOLS CO.,LTD.
Ningbo Luban Electric Power Tools Co., Ltd, an American invested company, was established in Year 2002, with 10000㎡ modern plant and a group of experienced R&D talents and managerial talents. Luban specialized in manufacturing High Quality Plastic Recovery Tracks, 4x4 Off-Road Recovery Traction Board,Sand Tracktion Board, Sand/Snow/Mud Ladder ,Perfumer Diffuser, and all kindls of Hand and Power Tools and so on.
Luban has a subordinate foreign trade company named Ningbo Aye International Trading Co., Ltd which located in Ningbo,China and was founded in Year 2010. Aye Trading company was mainly specialized in exporting 4WD Off-road Sand Tracks Recovery Tracks, Scent Aroma machine and hand and power tools like
Cut Off Machine, Electric Miter Saw,Bench Grinder,Rotary Hammer,Electric Planner, Electric Blower machine, Brick Trowel and Plastering Trowel, Hinges, Screwdrivers, Hex Key, Drop Tool,Handsaw, Garden Prunner and so on.
We have been always supplying the best quality products for each of our respected customers. All our products are in outstanding performance, they are selling well all over the world Like Australia, Indonesia,Philippines,Brazil,Spain,Dubai,Korea,Tailand,Bangladesh ,Iran,Ukraine etc- The perfect after-sales service won praise from all the customers.
- Company Name: NINGBO LUBAN ELECTRIC POWER TOOLS CO.,LTD.
- Representative: Yunqing Cai
- Product/Service: Plastic Recovery Tracks , Sand Tracktion Board , Snow/Mud/Sand Ladder , 4WD Off-Road Recovery Tracks , Scent Air Machine , Hand and Power Tools
- Capital (Million US $): 1000,000RMB
- Year Established: 2010
- Total Annual Sales Volume (Million US $): US$5 Million - US$10 Million
- Export Percentage: 81% - 90%
- Total Annual Purchase Volume (Million US $): US$5 Million - US$10 Million
- No. of Production Lines: 10
- No. of R&D Staff: 5 -10 People
- No. of QC Staff: 5 -10 People
- OEM Services Provided: yes
- Factory Size (Sq.meters): 5,000-10,000 square meters
- Factory Location: No,3030,Tiantong South Road,Jiangshan Town,Yinzhou District, Ningbo, Zhejiang
- Contact Person: Mr. Cai
- Tel: 86-574-88070042
Premium Related Products